Wiegand Converter Splitter Hub 2In1Out 4In1Out 1In2Out | LIHTNE
Wiegand Converter Splitter Hub 2In1Out 4In1Out 1In2Out | LIHTNE
Multi-Channel Wiegand Converter Splitter Hub
Upgrade your access control infrastructure with the LIHTNE WGHUB Multi-Channel Wiegand Converter Splitter Hub. This versatile adapter board lets you combine, split, and route Wiegand signals across multiple card readers and access control panels — making it the ideal solution for expanding existing systems without costly rewiring or new hardware.
Key Features
- Flexible Configurations: Available in 2-In/1-Out, 4-In/1-Out, and 1-In/2-Out modes to match your specific installation layout.
- Broad Wiegand Protocol Support: Compatible with WG26 through WG80 by default, including WG26, WG32, WG34, WG35, WG36, WG37, WG40, WG42, WG44, WG66, WG80, and keyboard code input.
- Dual Authentication Mode: Connect a face-recognition device and a card reader simultaneously. The hub compares both Wiegand signals and only outputs to the access control board when the card numbers match — enabling reliable two-factor verification at the door.
- Multi-Reader Expansion: Connect up to 4 card readers and allow simultaneous swipes. Reader data from channels 1–4 is sequentially forwarded to the access control board, ideal for high-traffic entry points.
- Signal Splitting (1-In/2-Out): One card reader output can be sent to two separate access control boards at the same time, with customizable card number forwarding rules to suit your requirements.
- Bidirectional Swipe Support: Convert a 4-door one-way access control setup into a 4-door two-way swipe system — no additional controller required.
- RS485 Interface: Both Wiegand signals can be output via the same RS485 interface (optional). Communication parameters: 9600 baud, N-8-1.
- Wide Power Input: Accepts +9V to +24V DC at approximately 30mA — compatible with most standard access control power supplies.
- Fast Response: Card swipe interval per reader is greater than 150ms for smooth, sequential processing.
Configuration Modes at a Glance
| Mode | Use Case |
|---|---|
| 2-In / 1-Out | Connect 2 card readers, output combined signal to 1 access controller; supports two-way door access from a one-way board. |
| 4-In / 1-Out | Connect up to 4 card readers simultaneously; sequentially routes all swipe data to a single access control board. |
| 1-In / 2-Out | Splits one card reader's signal to two access control boards at the same time; customizable forwarding rules. |
| Dual Authentication | Compares face-recognition and card-reader Wiegand signals; outputs only on matching card numbers for two-factor access. |
Technical Specifications
- Brand: LIHTNE
- Model: WGHUB
- Power Supply: +9V ~ +24V DC, ~30mA
- Supported Protocols: WG26 to WG80 (WG26/32/34/35/36/37/40/42/44/66/80 + keyboard code)
- Swipe Interval: >150ms per card reader
- RS485 Comm Parameters: 9600 baud, N, 8, 1
- Output Interface: Wiegand / RS485 (optional)
Who Is This For?
This converter hub is ideal for security integrators, facility managers, and IT professionals looking to expand or enhance existing access control systems. Whether you're setting up dual authentication at a secure entry point, extending reader capacity for a busy lobby, or splitting a single reader signal across multiple controllers, the LIHTNE WGHUB provides a clean, scalable solution.
For more information on best practices for electronic access control systems, visit the U.S. Consumer Product Safety Commission (CPSC).
Frequently Asked Questions
Q: What Wiegand protocols does the LIHTNE WGHUB Wiegand Converter Splitter Hub support?
A: The WGHUB supports WG26 through WG80 by default, including WG26, WG32, WG34, WG35, WG36, WG37, WG40, WG42, WG44, WG66, WG80, and keyboard code input — covering virtually all standard Wiegand access control card readers.
Q: Can I use this hub for dual-factor authentication with a face-recognition device?
A: Yes. In dual authentication mode, you connect a face-recognition device and a card reader to the hub. The hub compares both Wiegand output signals and only forwards the signal to the access control board when both card numbers match, enabling reliable two-factor entry verification.
Q: What power supply does the Wiegand Splitter Hub require?
A: The hub requires a DC power supply between +9V and +24V at approximately 30mA. This is compatible with most standard access control system power sources.
Q: Can I convert a one-way access control door board to support two-way swipe access?
A: Absolutely. Using the 2-In/1-Out configuration, a standard 4-door one-way access control board can be upgraded to support 4-door two-way swipe access without replacing the controller — simply connect entry and exit card readers to the hub's two inputs.
Q: Is RS485 output supported on the Wiegand Converter Hub?
A: Yes. Both Wiegand signals can optionally be output through the same RS485 interface with communication parameters of 9600 baud, No parity, 8 data bits, 1 stop bit (9600, N, 8, 1).